Important: TV mount designs can vary widely, so always follow the manufacturer’s instructions for this step. Mount Your TV To The Wallįor the last step, lift your TV, line the TV plate with the wall bracket, and connect them. Then, attach the plate to the back of your TV using the included hardware. Connect The TV And The Mounting Plateįind the mounting plate attachment holes in your TV and remove any packaging (if your TV has a stand, now is the time to remove it). Hold the mount against the wall and drill the mounting screws into the pilot holes. Install The Mounting Bracket To Your Wall Pre-drilling holes can help prevent the screw from cracking the wall as it goes in. Using the appropriate masonry bit, drill the pilot holes where you made the marks. Mark the places where you’ll drill the holes. Hold the mount up to the RV wall where you plan to attach it, and use a level to keep it straight. Infrared thermometers have many other uses around the RV, for example, checking brake and tire temperature.Ĭlicking this link to make a purchase may earn us a commission at no additional cost to you. You will see a difference in temperature as you scan the surface since there is no insulation at the studs. This works well if there’s a big temperature difference between the interior and the exterior. Contact the manufacturer for a print of where the studs are.Knock along the wall until you find a stud.So, here are a few other ways to locate those hard-to-find studs: Unfortunately, finding a stud in RV walls can sometimes be difficult. Tip: If your stud finder supports it, look for any electrical wiring or plumbing behind the wall, as well – basically, anything you do NOT want to drill a hole into. Use a pencil or painter’s tape to mark its position. So, hover your stud finder across the general area of your chosen location until you find a stud. And it may not be in the location you want to mount your TV. In our experience, that sticker is not always a good guide. Some RV manufacturers will place a sticker on the wall that identifies the TV backer location. Once you know exactly where to mount your TV, it’s time to find the wall studs to mount it to. Tip: Sit down in the chair or bed you plan to watch TV in and have someone hold the TV where you plan on mounting it to ensure it’s in the spot you want. So, take your time when positioning your TV. And even with adjustable mounts, the amount you can raise, lower, and change the viewing angle of your TV is limited. Unless you bought an adjustable mount, changing your TV’s height and the viewing angle can be challenging once installed. If you want to install a new flat-screen TV in your existing TV box (where the old tube TV sits) or under a cabinet, check out our guide on how to install a flat screen TV in an RV. TV Mount Installation Processīelow we detail exactly how to install a TV mount to an RV wall. You can buy paintable cable covers to match your wall’s color – a simple and cost-effective solution.Ĭlicking this link to make a purchase may earn us a commission at no additional cost to you. If your RV layout makes these options impossible, don’t worry. It’s easier to see, and you don’t have to leave a mark on your wall! Cable Covers (Optional)įor a neater look, route your cables through the RV wall, tie them neatly together, and tuck them behind a table, stand, or other decor. Once you’ve located your wall studs, mark them with painter’s tape. In a regularly-moving environment like an RV, a little bit of extra support goes a long way. You can apply industrial adhesive to your screws for stability. Having an extra pair of hands to hold things in place or help you carry the TV will make this project much faster and infinitely more manageable. However, sometimes a stud finder may not work as intended in certain RVs, so we cover alternative methods for finding a stud below. Without a stud, your RV’s wall surface alone won’t be able to handle the weight of your TV, and you can potentially create an expensive mess. Stud FinderĪ quality, deep-scanning stud finder will help you locate the spots in your RV wall that provide the best support. With a level, you can avoid making unnecessary holes in your RV wall and a crooked TV. Trusting your eyes alone is a disaster waiting to happen. You will need masonry bits and a Phillips head bit to create pilot holes and drive the mounting screws. We recommend a power drill for a much more straightforward process. How do you screw into an RV wall? A regular screwdriver will work, but it can be laborious and time-consuming. Clicking this link to make a purchase may earn us a commission at no additional cost to you.Ĭan you use a regular TV mount in an RV? Yes, but keep in mind that if it has an adjustable arm that doesn’t lock, you should remove the TV from the mount during travel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |